
Tom, Horsetown USA ranch home, Norco
Granite Countertop Installation
- Material
- Colonial White granite
- Size
- 45 sq ft ranch kitchen
- Est. investment
- $3,600 to $4,600
- Est. duration
- 1 to 2 days
Long ranch kitchen with two corners and a 1980s laminate top
Riverside Custom Countertops offers undermount sink cutouts & installation in Riverside, cutting the sink opening in our shop, polishing the reveal and mounting the basin under granite, quartz, marble and quartzite, whether it is a new kitchen, a bar sink or a drop-in you want to convert.
A sink hanging under the stone shows its cutout edge every time you wipe the counter, which means the opening has to be square to the sink, smooth and polished. A slab laid on a saw table with full support cuts cleaner than a top propped over cabinets, and the edge can be polished before the stone ever reaches your house.
We cut to the sink you bought, not to a catalog size. Our crew works across Riverside, Norco, Corona and Eastvale, and we ask for the sink or its exact model number at the template visit so the opening, the reveal and the clip positions are drawn from real dimensions.
What you can hold us to

Tom, Horsetown USA ranch home, Norco
Long ranch kitchen with two corners and a 1980s laminate top
Investment and duration figures are estimates. Your written quote sets the final price and schedule.
Cutting at the shop prevents the chipped corners and wavy lines that come from sawing a finished top over cabinets. Stone is brittle along a freshly cut edge, and a saw working with no support underneath will flake the underside and sometimes crack the narrow strip at the front of the sink.
In the shop the slab lies flat, the cut is made wet so the blade stays cool, and the inside edge is ground through several polishing steps. By install day the opening only needs to meet the basin, and a crew of 2 to 3 installers does that in a few hours.
Reveal describes the strip of sink lip visible inside the opening, and you choose it before any cutting starts. Each choice changes how the counter looks and how it cleans.
We show the three options on a sample at the template, then mark the chosen one on the stone.

| Reveal | Look | Cleaning | Best for |
|---|---|---|---|
| Zero | Flush, one continuous line | Wipe straight into the bowl | Most kitchens |
| Positive | Thin rim showing | Easy, rim is a small step | Sinks that vary slightly from spec |
| Negative | Stone overhangs the basin | Harder, crumbs sit on the lip | Design-led kitchens |
If you cannot decide, zero reveal is the safe pick for a working kitchen.
A polished sink cutout on a new top is an estimated $150 to $400 per opening, and on tops we fabricate it is usually folded into the job so you do not see it as a separate line. Retrofits and sink swaps are priced after we see the counter.
What moves the number is the sink shape, the stone, and whether the basin needs extra support. A small bar sink costs less to cut than a large farmhouse or a heavy cast iron bowl.
Polished reveal, radiused corners, clips and sealant
A smaller bowl cut with the same process as the main sink
Enlarge the opening, polish the new edge, mount the basin
Remove the old sink, remount and reseal the perimeter
Rails or frame sized to the full weight of the bowl
Drilled to the layout you choose at the template
Investment and duration figures are estimates. Your written quote sets the final price and schedule.
These figures are estimates, and the written quote we hand you after measuring the sink and the stone is the number that counts. A retrofit is the one job where a bad surprise can appear, so we inspect the counter first and tell you what we find.
Sinks are bought by the homeowner or the contractor more often than by us, so please send the model number early. A basin on backorder can hold up an install more than any cut ever does.
An undermount sink is carried by mechanical hardware, not by sealant. Metal clips are epoxied to the back face of the slab, the bowl is pulled snug against the opening, and a sealant bead closes the joint so moisture has no path into the cabinet.
Silicone alone can let go after a few years of hot water and the weight of dishes and a full basin. We set the support to the weight of the sink, and for heavy cast iron or a large single bowl we add rails or a frame so the load rides on the cabinet rather than the stone edge.

You can often swap a drop-in for an undermount when the stone is sound, thick enough and has room around the new opening. We enlarge the cutout, polish the fresh edge and mount the new basin, which costs far less than replacing the top.
We check first for cracks, seams and how close the dishwasher run or a cooktop sits. Cutting a bigger hole beside an existing crack is how a counter fails, so some retrofits get a no from us, and a new top is the better answer. In that case countertop replacement is the route we quote.
Four stones take an undermount bowl well, and each behaves a little differently at the cut edge. Our granite countertops and quartz countertops polish to a crisp reveal, while marble tops need a sealed edge because the cutout is where water sits most.
A slim 2cm slab or a laminate-faced base may call for a plywood sub-top under the bowl, and we raise that at the template instead of discovering it on install day.

A sink opening should never sit across a seam, and it should leave a solid strip of stone at the front. The narrow band between the cutout and the front edge is the weakest part of any top, and it is where cracks tend to start under a heavy load.
When the layout leaves too little stone, we say so at the template and move the sink a little or shift the seam. A few inches of change on paper costs nothing, and it saves a cracked piece in the shop. Seam planning is covered in more detail in our seam matching work.
We cut and mount undermount sinks within about 35 miles of the Riverside shop, with most of the work in Norco, Corona and Eastvale. Kitchens, bars and outdoor prep stations all use the same shop process.
If your sink is part of a bigger kitchen countertop installation, the cutout is included in the template and the install visit.

One crew templates, cuts and installs, so the person who measured the sink is the person standing in your kitchen on install day. The work carries our 1-year workmanship warranty, so a sink that sags or a joint that opens comes back to us.
We would rather turn down a retrofit that is likely to crack than cut it and hope. If the stone is not up to the job, we tell you plainly and quote a safer path.
In many kitchens it is, provided the slab is sound and thick enough, and we inspect it before quoting.
A polished cutout is an estimated $150 to $400 per opening, and the quote you sign fixes the real figure.
Yes, the sink itself is best, with the full model number as the backup, because we cut to the actual basin and never to a guessed size.
A reveal is how much sink rim shows inside the opening, and zero reveal is the best pick for most working kitchens.
Yes, because the hardware glued beneath the slab carries the basin, and heavy cast iron gets extra rails.
Granite, quartz, quartzite and marble all work, while a slim top may need a sub-top before it can carry a bowl.
The opening is cut in the shop before install, and mounting the sink on site typically takes a few hours.
Usually yes if the new sink is the same size or the stone has room, and that job is often finished the same day.
Request a free estimate, tell us the sink you have chosen, and we will confirm the cutout, the reveal and the support before any stone is cut.



Start to finish
We take the sink model, check the stone and cabinet, and draw the opening.
You pick zero, positive or negative reveal from a sample.
The opening is cut wet and polished before the top leaves the shop.
The basin is clipped under the stone and the perimeter is sealed.
Where we work
Call us or send the form, and we will book a site visit and a laser template.
Calls only, we do not receive text messages.